Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Dears,
I am developing a board based on the nRF52-DK board and I noticed the technical documentation does not include the voltage ratings of the capacitors used. Could...
I am trying to make a large BLE sensor network, hypothetically anywhere from 20-100 devices in a STAR configuration. I see there is a 20 max limit on concurrent connections...
Hi,
I am trying to send a simple message from server to client in mesh 2.0.1. I am following this post for the same. I successfully sent a message from client to server...
When I want to connect the jlink use j-flash.exe.it report the follow message.My
Connecting ... - Connecting via USB to J-Link device 0 - Target interface speed: 4000 kHz...
I am using the nRFgo Studio to flash the nRF52 Development Kit. I am using the SDK V14.0 and its libraries to grab RSSI values by writing code to the N52832 BLE MCU IC. I...
Hello,
I have configured the SPI0 module in master mode with EasyDMA. I use the below code to send data
In the output I get the string "SPIM TEST" and with extra...
We are using a nrf51822AC Chip with SDK 9 and Softdevice S110. We want to use Segger Embedded Studio 3.40.
I have imported the BLE HRS Sample from the SDK an did the settings...
The question is in the title. I found this addition a nice optimization to be used where available (that is to this day, on NRF52840 only, according to the latest Product...
Hi,
I'm trying to run the ble app uart central example using SDK15 with Embedded Studio.
When building the project, I encountered an error in retarget.c, where the error...
Hi,
I have a couple of WT51822-S4AT boards I would like to use to send data from a PC to one board via UART and then pass the data to a microcontroller connected to the...
Hello, i'm trying to store data in the flash, i manage to write a correct data in the flash but when i try to read it the address is erased.
I use this function to write...
Hello, everyone~
I want to use a nRF51824 to scan a specified smart phone and use the RSSI to estimate the distance. Is there a simple and basic example of this funtion...
Hello everyone
I have a small question about Mesh_gatt_pdu_type_t in light_switch_example.
When my NRF52 connect with smartphone over BLE mesh proxy, my smartphone will...
I am developing my project in a nRF52832 custom board. I am working in SDK v12.2.0. My application program is based on ble_app_uart.
It seem a bug about the defined characteristic...
