Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
Hi
I've just done a few tests with the FDS system of the SDK12.2. My observation is, that the FDS doesn't properly use all assigned flash pages to reach a maximal lifetime...
Hi,
I am quite new to nRF51 development so please excuse me for my mistakes or not using right words if any. I have some code that fully works on the official nRF51 DK...
Iam using softdivice 110 and sdk 10.0.0, when i connect UART RX pin to TX of STN1110 the processor doesn't start until I remove connection between RX of nRF51822 and TX of...
Is this antenna pattern and design for our custom board is fine? we are using the nrf51822 with matching circuit.
Please put your valuable suggestion from your experience...
Hello,
I am using nrf5 sdk 12, and I have read the documentation in ble_gap.h for NRF_ERROR_INVALID_STATE and I have seen a few questions on this forum, and what I understand...
I have an application (with SD S212) that uses NFC. Ideally, the processor would be in idle most of the time, waking up only to FIELDDETECTED and FIELDLOST events.
The...
Hello,
in nRF52832_PS_v1.2.pdf, in the timer section for the MODE register, there is a third mode named "Low Power Counter" described, without any description in the rest...
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Has the nRF51822 already got the QID and BQB certificate? Our BLE module using nRF51822 doesn't do the QID and BQB test. Can our product using the BLE module add the BLE logo...
Hi,
We need a 2.4Ghz smd antenna, not to emit bluetooth but a in-house protocol we are testing.
It will need to fit on a pcb and have good performance, and production...
