Testing with NCS 3.0.1 and nRF54L15-DK. I would like my devices to be able to work as channel sounding initiator as well as reflector role. In my own code I have integrated...
Are there any samples for proprietary radio based on connect SDK?
https://www.nordicsemi.com/Products/Wireless/2-4-GHz-proprietary
I am not interested in gazelle and wanted...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
hi all,
i am a begineer to nordic. i want to send data over ble and read that using master control pannel.
please say wat api i want to use and how to use. please give detail...
Hello I'm new of nRF seriese.
nRF51822CEAAD00(0x004d)
SD130 ver2.0.1
kail Ver5.18
SDK11.0.0
I just finished the tutorial and now I'm making my new project with twi...
Hi, I am using Heart Rate rate monitor code to send floating value instead of unit16_t.
I am using the heart rate service to send the data. Instead of using simulated sensor...
Hi,
I am new to nRF5x BLE devices.
I need to create a project and would like you to help me out.
I need to connect two nRF51822 devices. If one of the devices goes...
hi dear officers
since the datasheet states that value 1 stand for connected, does it mean this pin is active-low.
in order to physically reset the device, could i connect...
I have tried ble_app_uart_c project in SDk 9 , SDK 10 or SDK11 , but they have the same problem.
Problem is that slave(SDk 9,ble_app_uart) can send data to master(by terminal...
While trying to bond an iPhone 6 (running nRF MCP App) with an nRF52 with S132 2.0.0 I encountered the following error:
On the first try, when the iPhone is not yet paired...
I am trying to set up a button interrupt by adding the following functions:
void button_interrupt_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_gpio_pin_toggle...
Dear Sir,
When nRF51822 is a slave, it should be updated software through Master(Z-Wave CPU) remotely.
How can we update SoftDevice software in nRF51822? UART, SPI, or...
My code detects an external signal using GPIOTE. Whenever the signal falls, GPIOTE calls a handler, audio_stimulus_handler . The code is shown below. Essentially, after detecting...
I have a nrf51-dk. I would like to the pincode to be stored in some configuration settings which is written in non-volatile memory. I do not want the pincode to be hard-coded...
