Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
I'm having some trouble with the discovery module. The way the service I'm connecting to has the same UUID for the Bluetooth LE service as for its characteristic. I get this...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
Hi.
I read on the download site of the nrf command line tools that they are being deprecated.
I want to be sure that i'm correct here: 1. nrfjprog is replaced by nrfutil...
Hello,
we are trying to perform FOTA updates with default SLM application based on SDK 2.9.0, but the application always aborts unsuccessfully.
Via AT interface the application...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
I am in the process of migrating to NCS 2.7. My project includes NSIB, MCUBoot, TFM, and the application. Everything works fine with multi-image builds.
However when using...
I am trying to port blinky_blank (no SoftDevice) to my target and started by creating a custom_board.h header file with correct GPIO pins for the LEDs and duplicating blinky_blank_pca10040...
Can anyone help me reading IO capability in Android? Basically there is a known bug in some Android versions across different manufactures where Android reports wrongly IO...
I want to use chacha20 cypher to encrypt and decrypt a 64 byte message and send it over BLE. I tried using wolfSSL, cifra both of which provides the implementations but there...
Hi,
To measure the transmitted RF power (to reach EN 300 328) we Need some ATT commands to set fix channel and maximal output power. In additional we test the EN 55022...
In this previous discussion on minimizing power consumption on the NRF51-Dongle, it says:
You are using evaluation kit or
development kit and LEDs are connected
on...
My system is a BLE peripheral with 2 states. There is a characteristic that represents the state, and it can take 2 values: 0 and 1.
You can read the state, write it (force...
When the supply voltage drops below 0.6V and then get back to 3.3V the nrf51822 starts up in an undefined state and often some flash pages are corrupt after that. Is this...
Hello,
We're currently running softdevice s310 v2.0.1 with SDK 7.1.0 on the nRF51422-QFAAE0 (ie. rev 2). We're planning on upgrading to the nRF51422-QFAAF0 (ie. rev 3)...
Hi!
I was using SDK11 alpha previously and when the official version (89a8) got rolled out I started integration. First thing was the missing S210 and S130 softdevices...
Hi together,
I'm using the NUS example (NRF52832) for client and peripheral, which is running quite well. My goal is to inform the peripheral application when notification...
Hi,
I am using nrf51822 chip and i have compiled the TCP Client example from IOT SDK in eclipse.I am using Master control panel as a central device to discover the device...
I want to measure a current consumption for the 3rd-party evaluation board which has 32MHz crystal and 32KHz crystal, and there is not PO.18 on the 3rd-party evaluation board...
Hi,
I use nRF51822.
Is it possible to change a beacon timing of the advertiser by a trigger of the acceleration sensor in the advertising mode?
Thank you for any...
Hello everyone,
I compiled the nrf51-app-button-examples without any error and warnings but it is showing me this error (No cortex -M Device found in JTAG chain / Target...
According to PCA10028_Schematic_and_PCB.pdf (Rev 1.2.0), page 7, there should be SB22-25 surrounding TP5-8:
On my PCA10028, I have TP5-8, but no SB's there:
What...
