Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
We are implementing scan functionality in nRF51. I would like to understand if anyone has tested or tried to scale this functionality when there are thousands of beacons around...
Hi everyone,
I was wondering how GAP calls and events are synchronized within the SoftDevice.
Example:
// conn_handle is updated in the CONNECTED and DISCONNECTED...
The Android Master Control Panel app has an option to remove bond information (which works). But the API for it is hidden .
I'm just wondering if you use reflection to...
We are trying to replace an existing solution that uses a custom Service with 4 Characteristics. Unfortunately none of those share the same base UUID.
Basically the Service...
Ok - I'm trying to get my arms around this bootloader process.
I am using the nRF5_SDK_11.0.0_89a8197 SDK along with the PCA10040 develeopment kit.
I also am using IAR...
I'm trying the run the smart remote 3 v1.1 firmware built using IAR.
The firmware fails to init the touchpad and enters a forever loop.
The program only builds with optimization...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0. In my application i plan to use RFX2411N PA/LNA module. In datasheet of RFX2411N, I found that it can be used in...
Trying to qualify our design with Bluetooth SIG.
NRF51422 QFN48 nRF51 SDK v10.0.0 SD 310
When I use QDID 62791 to generate a test suite for PTS on the SIG website, the...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hello,
I am working with the nRF52 DK, SDK 11 and especially with the ESB protocoll. I started with the provided example esb_low_power_ptx/prx.
In the documentation...
Hi,
I wish to encrypt my application to protect my code. I've tried running my hex file through openssl
openssl enc -aes-128-ofb -nopad -nosalt -e -K XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX...
There are an example which based on Nordic's implementation of BSD Socket API (the client-side).
Also, I have seen the lwIP Socket API in nRF5 IoT SDK, but, there no app...
Hi,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0 and S130. I wanted to perform the task below.
I have a couple of nRF Beacons and want to program one of it...
Hi.
We just received few new nrf52 boards. They are same PCA10040 v1.1.0 as previous ones, but these have date of 2016.21 stamped on them instead of 2016.09. Problem is...
