I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
I've been working on a peripheral wich accepts Just Works pairing requests and I'm completed at all points but the pairing itself. The device advertisises and connects successfully...
Hi,
Currently I use a custom linker section for my code.
.my_code_section : { PROVIDE(__my_code_section_start = .); KEEP(*(.my_code_section)) PROVIDE(__my_code_section_end...
I’m trying to implement DFU upgrade of NRF5340, I can send the image (./build_5340_app/build/signed_by_mcuboot_and_b0_s1_image.bin) to the device when running and it seems...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
I am implementing DFU using my own transport to retrieve the binary image from AWS.
I'm developing in 2.6.0.
I am using the DFU TARGET libraries.
When I start my download...
So i am using a LiPo battery at 4.2V and running my nRF51822 at 2.0V. Is it safe to connect the battery to one of the I/O pins to read off the battery voltage (as to calculate...
Hi there.
We are developing an IoT device (we are planning to use nRF24L01+) we would like to implement with microchip uC, the question is if there is a library available...
Dear Nordic Developer Zone,
I am able to ask a Silicon temperature measurement, but not to correctly interpret the answer.
After last measurement, I have got 0x29C....
Hi,
I need to have long attributes. So I need 'Read Blob' operation for read and Queued writes ('Prepare Write' and 'Execute Write'). Does Soft Device for nrf51822 support...
Hello everyone , can i use UART which is not a services or characteristic in bluetooth low energy . It will result in some question or bad effection?
By the way . why I cannot...
Dear all:
recently, I follow heart rate profile to write custom BLE profile,but I also went to a number of issues. how to wake up the device when entered power system off...
Hello,
This is the first time i use NRF8001 chip, i was reading the ic manual nrf8001_PS_v1.1.pdf (see attached file).
It was written that in case i used DC/DC converter...
Hello,
I checked Nordic website for layout of NRF8001 but i didn't find.
Please if some one can share a qualified RF-layout.
Help is appreciated.
Regards,
Hisham
from training document from Nordic company(see the attachments),it mentioned that we can add scan response .but i can not find any information in BLE_HRS demo.could you tell...
Hello,
I made a PWM with the TIMER2 of my nRF51822 (with the SoftDevice) and was working fine, till I read that I should not use the "NRF_PPI" functions and use the "sd_ppi_XXX...
I've got an nRF51822 development kit that I'm trying to get started on. I've gone to Kiel and downloaded uVision 4 (mdk472_a). I install it with all default settings and it...
Hi,
I add UART support using IRQ on the "ant_hrm_tx" example code.
and I'm sending packet of 4 bytes that contains: Delimiter,HeartRate,Battery,Delimiter
the frame...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
