Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
hi,
is it possible that we can use s120 stack as a central, at this stage to work with our customized profiles?
or it will support only SIG profiles
regards & thanks...
Hello,
I've completed the ble iBeacon like application we are working on, with some custom GATT services/characteristics as well.
When I use LightBlue on a MacBookPro...
There is a check box on nRFgo Studio, Lock entire chip from readback. But a lot of chip can not burn one by one
Can I use AES block encryption to do this?
Hi
We are investigating Hong Kong certification for our nRF9E5 based equipment in the 868 band
The snag seems to be that required channel centre frequencies are "odd...
Hi,
My setup is a nRFgo QFAA FA with S110 v.6.0.0 and Motherboard. I am using the latest SDK 5.1.0. The Master Control Panel drives the nrf51822 USB development dongle...
Hi,I have a Nrf8001 module, use a arduino to control it.
Now,I can use this module to connect IPHONE APP(BLE Probe and LightBlue),sending and reciving data are all ok,the...
Hi Nordic Devs,
First, thank you for excellent documentation and sample code for use with your hardware. It's been tremendously useful already!
I'm pleased to own an...
Hi,
i have some trouble with my watchdog in application. If i does a System_reset (no SD Method because i disabled it before) it sometimes top at this point and does nonsense...
Hi,
We'd like to using nRF51822 to setup an environment which have 2 peripherals and 1 multi-connection central.
Peripheral 1 : reading some data from the car(OBDII...
Hi, we add two characteristic as TX/RX.
We are ready to use them to transmit data and receive data with phone
One for transmit the control command and get respond command...
We have hardware that uses the nRF905 transceiver that inputs different addresses into the nRF905 TX messages based on the specific unit (TX_ADDRESS varies based on unit serial...
Hello
We have devices who uses nRF905 for transmissions between them. When we receive messages we use the AM and DR signal to determine if a message is read correctly. The...
GPIOTE gives us 4.
LPCOMP gives us 1.
What else?
I am working on something related with external interrupts.
Doesn't have problem in my project, but I just always...
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
