During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello Nordic team,
I am using nPM1300 and nRF5340 in my custom board. I am using also Renata ICP621333PA-01 battery in my design. In order to prolong the battery life, I...
I am using a Mikroe development board with the nRF9160 to establish an LTE connection and send MQTT messages to a broker. The application successfully connects to the network...
I have used the nRF52832 on a few dozen projects, usually at 3.3V etc. On this project I have it at 1.8V, which may be related, but spec is 1.7V min, and the 1.8V supply is...
Hi Noridic team,
I am developing with nRF5340, and I added the following configuration to the prj file:
CONFIG_SPI_NOR_INIT_PRIORITY=75
However, I got the following...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
I am porting the LoRa Basic Modem to the nRF52832 , using the nRF5 SDK and Segger Embedded Studio (SES) . In my application, I am using SoftDevice and implementing FOTA ....
Hi,
We recently updated our NRF Connect SDK from v2.2.0 to v2.7.0.
After porting to the SDK v2.7.0 we are not able to build the project with DFU enabled. We get below...
What is the best method to ensure the nRF9160 LTE functions on a PCB during assembly with minimal test equipment? Our thoughts were to search for available networks using...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I'm working with a client's existing product. It has an external MCU connected to nRF52832 via SPI.
The nRF application & SDK code are compiled inside the external MCU source...
I now want to use the 52833's board to burn the host program and then connect to other nordic slave devices. But now I put \nRF5_SDK_17.1.0\examples\ble_central\ble_app_uart_c...
Hi All,
1. The SDK used in VS code is version 2.6.1, and running the periphral_uart demo can print in rtt, but not in sid_end_ device
The official routine is used for...
Hi
First of all i am quite new to nRF SDK so if the answer to my question turns out to be trivial then I am sorry.
I am in the process of developing a Zigbee light switch...
I need to check if the Ethernet cable is connected or not, I am using the eth_click for ENC28J60. I see the driver does not allow me to see directly if the cable is connected...
Hello, How can I purchase a nRF9131 EK from Nordic Semi Sales? I was informed at the recent "Getting started with NR+ PHY" webinar that nRF9131 EK can only be purchased directly...
