hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I have recently updated to V2.1.1 and I can no longer get my BME280 sensor to work.
I am using the standard code from the samples directory,
my overlay file...
I am developing a product using the nRF52840. I am currently running into a difficult problem. I inquired about it 2 years ago, but it has not been resolved.
I need to process...
Hi, on the nRF52820-QDAA I am using pin 5 AIN3 / P0.05 as an GPIO output to drive a LED (active low).
This does not work in the software, when I drive the pin high with...
Hello,
NRF5340, NCS2.0.2, VScode
I designed a headset，MCU is 5340, and a external flash for DSP program.
the external flash connect to DSP and 5340 use SPI;
i can...
Hello,
I was able to build the nRF Desktop sample application on the nRF5340 platform, but when trying to debug, I get the following error:
Here is my build configuration...
Dear ,
I am going to use debug out function on RF5340 DK.
connection is as below: customer board conncet to nRF5340DK.
customer board use nRF52833.
I tried many times...
Hi,
I was just wondering if the nrf52840 Dongle is in some ways inferior to the other development boards in terms of its capabilities?
As I was going through the examples...
Hi,
I am using a nrf528409dk for my application development using nCS. I have various features from which I need to understand how to add some high priority features into...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
