I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Hello everyone.
I've got the nRF51822 Evaluation Kit and Dongle. The heartbeat demo is working, so I got the toolchain -- Nordic, Keil, Segger under Win7 -- set up correctly...
Hie,
Is it compulsary for us to send only 20 bytes of data or less than that in one packet in BT5 as we used to do it in BT4 to make BT5 compatible in communicating with...
Hi,
I want to develop a product with Bluetooth 5( NRF52840) capability, before starting development I wanted to know will the Bluetooth 5 devices(Peripheral) will be compatible...
Hi. When i use ble_app_uart i have problem with my device over uart. It does not response to my commands.
I'm using custom pcb based on nrf52 with nrf UART v2.0 android...
I have moved on to SDK12. But one old project using SDK10 now requires a 128 bit UUID.
I keep getting hard fault when I add UUID.
I noticed that there is no vs_uuid_count...
Hi Team,
I am using nRF5_SDK_11.0.0_freertos_dfu_060516.zip SDK. I have added NUS service with UART configurations in this code successfully.
When I am commented the DFU...
We have both nrf51 and nrf52 running DFU.
How can I identify on the mobile application side whether I'm connecting to nrf51 or nrf52?
They will need to get different firmware...
Hi,
Is it possible to know which type of advertising packet is being advertised by the slave i.e whether it is a connectable or a non connectable advertising packet by...
Hi,
So I have a HEX file with unit specific data that I upload to 0x00062000. This data is about 80kb so it leaves some space incase I need a bootloader in the future....
Hi:
I want to bond and change dev name and storage.
This is my storage dev name init code:
void my_flash_init(void)
{
uint32_t err_code;
pstorage_module_param_t...
Hi all,
i'm using an app_timer.
I need to use three timer for debounce of three button. In my case i have to discriminate the push of three button at same time. When all...
Hello Community
I have read the following threads:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
In order to know how to discover my services, including...
Hi
Does the CryptoCell in the nRF52840 support secp256k1?
In this documentation it says at one point Koblitz curves using fixed parameters, up to 256 bits, are supported...
I used to do with the iso7816 run on nRF51822 SDK9 and S110_v8.0. However,as the BLE stack is running, the iso7816 interface clock signal is abnormal. as the picture below...
Hello!
I have the board PCA10040 (nRF52 DK).
I designed two different programs:
SPI: I'm using the SPI communication to communicate with an external sensor (accelerometer...