hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
when ntfx_spis_init() is done , NRFX_ERROR_INVALID_STATE errer occured.
pcb_state is NRF_DRV_STATE_INITIALIZED.
my code is
int cc3235_spi_init ( void )
{
...
Hello, Hardware : nRF5340DK SDK : v2.6.1 Context : Creating a prototype using a Load Cell and transmitting its weight on BLE. Disclaimer : I'm new to the settings subsystem...
Hello,
We are currently helping one of our client develop a product using the nRF5340.
DK versions:
nRF5340-DK
PCA10095
2.0.1
Host OS:
Ubuntu 22.04.2...
I'm a beginner to nRF52840 board, and I'm currently doing the nRF Connect SDK Fundamentals . But I failed to build the Blinky Sample due to the following error:
I'm sure...
I am working with the module nrf5340-DK. I am searching for an example to use the QSPI with the onboard external memory, could you share an example? and the other question...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We have some queries related to power section which are, 1. can we an use the same power...
This one is throwing me for a loop. We have a very basic NFC component in our firmware that serves up a static NDEF file and wakes the MCU from a system_off state.
We have...
Hello All,
I am programming an nrf52480 using zephyr on a windows machine.
I am trying to write a bluetooth peripheral characteristic, ore specifically to the led...
When using two nRF5340 Audio DKs as bis_transmitter and bis_receiver respectively for the iso_time_sync sample, the iso_recv event is triggered.
However, in the respective...
Hi,
I use nRF52805 chip for BLE tag. FACTOR_MODE pin will be used for production stage. At F/W start point, F/W reads FACTORY_MODE pin, if the pin is high, F/W will enter...
I am trying to program nrf5340 using this command: nrfjprog -f NRF53 --program merged_domains.hex --verify --recover -r
It works fine if readback protection is not enabled...
Everytime I make a call to the usb_dc_ep_write function I get error -22 meaning invalid argument. I have tried everything I can think of. I tried sending a blank packet with...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice When using the ble_app_uart example, "Failed receiving NUS message. Error 0x04. " appears...
After discovering that MBEDTLS requires at least 48000 bytes of heap to function, I've had to desperately find some spare bytes to conduct a TLS session over WiFi using a...
