Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
At our factory, the employees would like to have the AT command set exposed of our nRF9160 devices.
Since we would like to use PPP-sessions with our modem, we would...
Hello,
I would be grateful if someone can help me to understand what I’m doing wrong or missing with my setup:
Basically, I’m using the UDP application with Thingy:91...
Using SDK 15.3 on the embedded side and Android 10 I think it is on the mobile side.
We've implemented whitelists and hanging onto the bonding information on the embedded...
Hello,
This is more of a general question about how to best assure that bluetooth is working. The problem in my setup is that i wont be able to access the chip physically...
Hi
I have gone through the ncs documentation and have couple of questions reg the difference in network core and application core and reg the developing solution using nRF5340...
Hello,
We have used the nRF905 in our products over many years. This time we have decided to design the circuit on a 0.8mm FR-4. The recommended layout and BOM suggest to...
Hello,
I've used the Nrf-Sniffer a zillion times before and I really appreciate the existence of this tool. Thanks a lot! Now, I want to run the tool on my new M1 MacBook...
Dear all
I am trying to figure out the range for the connection parameters, I understand that the connection intervals are range from 7.5ms-4s from the post here . But it...
HI,
I'm trying to get an OLED display over SPI working but since I've no reaction yet, I probed the output and noticed it seems to have no write data hold time between MOSI...
Hi Devzone Members,
I'm brand new to Bluetooth development, and I wondered if someone would be kind enough to advise me?
Am I looking at the correct Nordic kit to begin...
Hello,
we have experienced multiple times during testing that nRF9160 Modem reported CEREG 2. After that it stopped generating any notifications and stopped connecting to...
Adverting mode changing from BLE_ADV_EVT_FAST to BLE_ADV_EVT_IDLE. Could you provide example for changing adverting mode from BLE_ADV_EVT_FAST to BLE_ADV_EVT_SLOW mode?
...
Dear all
I use VS Code with nrf Connect v1.9.1, DK is nrf52833. It has been working fine in terms of debug, but today it stopped working and give me a message like this...
Hello, Nordic team
We have been studying Nordic for some time and are now in the stage of product research and development. We bought an nrf9160DK from a local agent at...
