hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I've been trying to debug a recurring hard fault around nrf_log_frontend_dequeue. This occurs sporadically (between 10-60min) into testing my firmware. When the fault occurs...
Hi all,
normally our system runs in low power mode. When triggering the SAADC the first samples (using oneshot mode) will be off (slightly too low).
I can work around...
Hi,
I need to create run time count that increases every 0.065536sec.
I found a way doing so by using HFCLK without any interrupts.
My questions are:
1) Are there...
Hi, I am working on the nrf52840 dongle using the softdevice.
I would like to know whether it is possible to add OTA DFU capability to the default open bootloader that allows...
Im quite new to development with the DK so bare with me.
Currently I am able to read digital values (0 and 1) from the potentiometer using pin P0.03.
I am using the function...
I had toolchain manager 0.10.3 and a project using NCS 1.91. Unfortenuately I have updated the Toolchain manager to 1.0.0 and now my project does no longer show up and the...
I have a NRF52840 based custom device that I can program just fine with a NRF52840-DK.
However, when I try to use a NRF52833-DK I can erase and flash the softdevice just...
Hi,
I work with nRF52840 DKs and I am working for indoor positioning system based on RSSI signal strength. I want the RSSI signal strength to be sensed and transmitted to...
Hi Devzone team,
My customer wants to design the LTE-M antenna for their tracker project in US market, do we have any antenna reference or design guideline? I see we have...
Hi,
I am looking for a BLE module that I can program to send a Thyrmistor signal 250 meters or more. The BLE module has to be small and able to collect A/D Convertor and...
Hi ,
I am trying to get GNSS on thingy 91 to work. It seems like I have the same issue as this thread:
I cannot get a fix. Currently, I am using the 1.3.2 firmware ( the...
Hello, I am developing a product using nRF52840. I use the DK board to debug and download.
However, I would like to implement a firmware update function using USB on my...
Dear,
we have a problem at the startup for our nRF52833-DK board powered with coin cell battery. nRf52833-DK doesn't start up with coin cell battery when running ble_app_uart...
Hi,
I'm trying to do a 2 channels adc reading to read a value of a potentiometer and a value of a battery level. When I try to make it, I saw that sometimes, the value of...
Hello Support,
For my Zigbee Coordinator development I use nrf Connect SDK 1.9.1 (for now), and VS, I like using Kconfig GUI as much as possible.
I'm trying to find some...
