hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, I'm using the nRF Mesh Library for Android and I'm looking at the data of a mesh network in JSON format. I don't see anywhere the sequence number of a provisioner. Where...
I am following the guide on this page: https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
I can build the firmware, but having trouble...
1， The SDK is nRF5_SDK_14.2.0_17b948a;
2, running the usbd_audio project; It don't control the volume by 52840;
3, Can you help me how to adding the volume control in...
We tried two build options:
1. thread version 1.1 with
# Set OpenThread NCP architecture CONFIG_OPENTHREAD_COPROCESSOR=y CONFIG_OPENTHREAD_COPROCESSOR_RCP=y
CONFIG_OPENTHREAD_THREAD_VERSION_1_1...
Hello
I'm using sdk v17.0.2 and I'm going to program using nrf52840 dongle.
I used nrf52DK because I didn't have nrf52840DK. And I'm going to upload the source code that...
Hi!
I am running Zephyr sample application for direction finding zephyr/samples/bluetooth/direction_finding_connectionless_rx with minor modifications on nRF52833 DK. I...
Hello, I'm developing a BLE application under nRF51422 based on SDK12.2 using softdevice S130. Now, I'm porting the application from Keil to IAR 8.11. There is no compilation...
Hi,
SDK nRF5_SDK_17.0.2
Using :\examples\peripheral\saadc
I want support for multiple peripheral in same project, so i took the saadc example and on top of it add Uart...
Dear Devzone,
We are testing GPS of our products based on nRF9160.
When we test in one car, the GPS signal is lost when the device is put inside this car. This situation...
While testing DFU for OTA ,after entering bootloader mode on my nRF52840 DK, the device doesnt show up either in the device manager or using nRFconnect and Jflash lite . when...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
