hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
Hi,
I'm working with a custom PCB, with nPM1300 and a microcontroller.
The problem is that working only with battery the nPM1300 VBUS pin show 2.4V and I cannot put...
Hello community,
I have been using my PowerProfilerKit2 successfully under Windows10 for several years now.
Currently I migrate my main system to Linux and would like...
Hello. I have developed a custom board with nrf52840. I am trying to get it running using a bluetooth hids peripheral example in nrf connect v3.1.0. And the main() runs just...
Hi,
I have a field application with a gateway (central) that connects to multiple peripherals for continuous data streaming, in this case 10 peripherals. I notice sometimes...
Has anyone successfully managed to control an led strip (WS2812) with nRF52840's I2S by any chance? I'm trying to use the led_ws2812 sample ( docs.nordicsemi.com/.../README...
Hi,
I'm working on a custom project and I was able to add and edit the overlay file according to my need till yesterday. Today when I tried to build the project I observed...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
I am following the tutorial on Nordic Dev Academy I have a nrf7002dk board and I flashed the code present here . The problem is even if I configure only one channel and I...
Hi Nordic,
I am currently working with the nRF52833 development board and facing an issue related to the APPROTECT feature. Each time I connect the board, the access protection...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
Hi there, I am trying to implement a UART handler on my nRF9151 that can Tx GNSS updates to my nRF52833. I am adapting this into the cellular/gnss sample, which is working...
