Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm using sdk15.0.0 and device nrf52840
I have 5 services among them only 1 service is for notifications and remaining services for reading and writes functionality. ...
Hi,
I build an Xamarin bluetooth application and I needs Plugin BLE nuget package Service, Characteristic and Descriptor UUID numbers. My device is nRF52840. I would like...
Hello everyone,
I am using UART in my project to send data and receive data
the issue is while I am debugging it shows or indicating at NRF_BREAKPOINT_COND;
but led...
Hi everyone,
I am developing a custom PCB that will integrate the nRF52840 SOC. More specifically I will use the MDBT50Q-1MV2 module from Raytac that is approved by Nordic...
I am working on nrf51822 and SDKV10, Softdevice S110. Firmware has implemented whitelist features and enabled bonding.When i bonded the device using nrfConnect App and the...
Hello,
My home application requires standard Wifi 2.4/5Ghz and Bluetooth 5 protocols for communication. I see that nRF has a proprietary Wifi, what are the differences ...
Hi need to change configuration which uart is used when mcuboot is going to serial recovery mode. I would like to have this set for uart1 by adding: Then I put nrf91 in the...
Hi, our product is one set of transmitter/receivier based on nRF24 series. Recently, the number of failures of receivers increases quickly, and most of failures are shown...
Hi community !
I got a weird problem for me. I got a program (BLE Mesh) which i flash on two nRF52840 Dongles, and i got 2 differents behaviour
The first one can be provisioned...
I used nRF connect on iOS to get values from a device. I can see the characteristic property as indicate: when connected it displays the values I need.
1- Is there any way...
HI,
I purchased the nRF51822 Bluetooth Smart Beacon Kit ( I knew it's discontinued ) to perform a quick and simple POC (put my custom 31 bytes for the beacon to advertise...
Hi All.
I have an issue with my development kit. I was working with DFU so I flashed the secure_bootloader project in my nrf52 DK so it is working fine.
But after this...
Hello,
I have an Adafruit Feather M0 Bluefruit LE with an nRF51822 chipset from Nordic and I am currently dealing with Bluetooth Low Energy, especially with profiles, services...
