I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Looking for the best ways upgrading from a nRF5 SDK / SoftDevice based design to Zephyr. in my case, the nordic bootloader / upgrade process is configured for UART.
It would...
When using custom 128-bit base UUIDs and 16-bit UUIDs to address services or characteristics within the formerly specified base UUID, it seems the Nordic softdevices always...
Hi, I am using nRF24AP1 for ANT+ purposes and I am looking for continuous scanning mode (the radio is active in receive mode 100%). The command Open Rx Scan Channel (0x5B...
when I have the line in my sdk_config.h, it overrides the and I end up with undefined reference errors.
right now I had to comment out the line to be able to compile the...
Hi,
I need to print the RSSI value to the nrf app or putty terminal to check the RSSI value.
I have gone the structures "ble_gap" file to get the RSSI value and calling...
Hi everyone
The following code is initiaizing the uarts correctly,but there is unpredictable behaviour in this case.
Whenever i disable the 1 UART sensor, works fine....
Hi all,
I am very new to the field of BLEs now I bought one BMD300 Evaluation board,and I want to use nRFgo Studio for the development is it possible to use nRFgo Studio...
Hi,
we are using nRF52832 ADC in differential mode. We have two channels connected, where other is presenting reference voltage 1,65V and other is +/-1,15V on top of that...
Hi. I am developing based on the multi-link central example. In the below code the PHY is set to BLE_GAP_PHY_AUTO.
I don't know if my example therefore is running at 1Mbps...
I saw several threads that talked about this, but I could not decipher an exact answer, so apologies if this is a Re-Ask.
I recently purchased a nRF52840 Dongle with the...
I am not able to Control GPIO PIN 14 In this program(BLE_UART) this PIN gets powered continuously . When the device connects to NRF App the power supply becomes Zero and after...
Hello.
Im in a stage where I need to transfer over our current old (ancient) libraries for SPI communications to a NRF52, where we use SPI to communicate to a certain slave...
Hello,
I have set up the Development Kit according to the following instructions and successfully activated the SIM card.
www.nordicsemi.com/.../GetStarted
Unfortunately...
Hi Everyone, Please help me understand what will be the average current consumption per hour with nRF52810 if I transmit 50bytes of data 4 times per hour and go to deep sleep...
