I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
When we add a uuid will follow the steps below
err_code = sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type);
// Add the service.
err_code = sd_ble_gatts_service_add...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart" as reference.
As I've researching nRF51 with Central device,
it returns
Packet 0 : 020105 0c094e6f726469635f55415254...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
My setup is as follows
1 Gyroscope + Accelerometer
1 RTCC
1 SPI Flash device
I want to set up the PPI to periodically sample the MEMS devices and the RTCC...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
hi,
i want to execute a block of code in which timer should start. and stop at end of the block. and the timing depends on manual interrupt. and restart again when the execution...
Im using a board that is not one of the officially supported nRF51822 boards. Im trying to get the ANCS example project to work, but It wont broadcast or even turn on the...
