I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Is using a 32.768 kHz crystal for clock of nRF52811 chip, the option to achieve minimum power consumption?
Is this only source of clock sufficient as the external clock...
Hello Experts,
I my main.c, I have defined my own TIMER1_IRQHandler() and when I build the code I get the error
Rebuilding 'timer_pca10100' from solution 'timer_pca10100...
i use ble_app_uart example code.
i have some problem that sometimes MCU can send data to application. but sometimes MCU can't..
ex) Success : 0x01 0x02 0x03 0x04 0x05...
hello i'm using nrf52840 dk board for communication with windows pc.
in nrf 52840 datasheet usb max speed is 12Mbps but my project based on "usb_cdc_acm" usb speed is 4Mbps...
Hi, we have project AoA direction finding. Firstly we have nrf5340 dk kits. Also CoreHW ANT3 2x2 matrix antenna kit. I run the direction finding connectionless demo on nrf5340...
Hi,
I am working with USB mass storage example from the SDK, and it works perfectly with the DK. Now I am working on my integrated PCB, and the same mass example doesn't...
Hi,
I am trying to get both the 802.15.4 stack and the BLE AoA stacks to run concurrently on an nRF52833.
Looking at the documentation here , it appears that it should...
Dear Sir/Madam,
I am trying to enable FEM support on zigbee/light bulb, and want to SKY66112-11 FEM working on Receive bypass mode. I set all pins at proper setting at initialzation...
When performing DFU with the same Android device + nRF Connect on the same target device, the speed becomes significantly slower on Android 15.
The attached image captures...
Hello. The visual study code uses toolchain v2.7.0, SDK v2.7.0 I'm trying to test the saadc example (in modules/hal/nordic/nrfx/samples/src/nrfx_saadc/) in "creat a new application...
Hello Nordic Team,
Our existing device using NRF52840 QIAA, we are plan to replace the QIAA package with CKAA package for size reduction. After I went through the SPEC,...
I´m testing the nPM1300 in a custom circuit with Zephyr on an nRF52 / nRF53 attached to it. It looks like the IC isn´t charging a battery. For testing I use the nPM1300-EK...
Hello,
Can I use in production nrf52840-DK as programmer to program E73-2G4M08S1C module on custom PCB?
What should I do to make the program code unreadable?
Hello, I need further assistance with the issue in the mentioned ticket ID, as it was closed by mistake. Could someone please reopen it so I can continue the discussion? ...
