Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
when ntfx_spis_init() is done , NRFX_ERROR_INVALID_STATE errer occured.
pcb_state is NRF_DRV_STATE_INITIALIZED.
my code is
int cc3235_spi_init ( void )
{
...
Hello, Hardware : nRF5340DK SDK : v2.6.1 Context : Creating a prototype using a Load Cell and transmitting its weight on BLE. Disclaimer : I'm new to the settings subsystem...
Hello,
We are currently helping one of our client develop a product using the nRF5340.
DK versions:
nRF5340-DK
PCA10095
2.0.1
Host OS:
Ubuntu 22.04.2...
I'm a beginner to nRF52840 board, and I'm currently doing the nRF Connect SDK Fundamentals . But I failed to build the Blinky Sample due to the following error:
I'm sure...
I am working with the module nrf5340-DK. I am searching for an example to use the QSPI with the onboard external memory, could you share an example? and the other question...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We have some queries related to power section which are, 1. can we an use the same power...
This one is throwing me for a loop. We have a very basic NFC component in our firmware that serves up a static NDEF file and wakes the MCU from a system_off state.
We have...
Hello All,
I am programming an nrf52480 using zephyr on a windows machine.
I am trying to write a bluetooth peripheral characteristic, ore specifically to the led...
When using two nRF5340 Audio DKs as bis_transmitter and bis_receiver respectively for the iso_time_sync sample, the iso_recv event is triggered.
However, in the respective...
Hi,
I use nRF52805 chip for BLE tag. FACTOR_MODE pin will be used for production stage. At F/W start point, F/W reads FACTORY_MODE pin, if the pin is high, F/W will enter...
I am trying to program nrf5340 using this command: nrfjprog -f NRF53 --program merged_domains.hex --verify --recover -r
It works fine if readback protection is not enabled...
Everytime I make a call to the usb_dc_ep_write function I get error -22 meaning invalid argument. I have tried everything I can think of. I tried sending a blank packet with...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice When using the ble_app_uart example, "Failed receiving NUS message. Error 0x04. " appears...
After discovering that MBEDTLS requires at least 48000 bytes of heap to function, I've had to desperately find some spare bytes to conduct a TLS session over WiFi using a...
