hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I got a brand new nRF52832 DK today and wanted to program it but the USB is not recognized at all therefore the nRF Programmer shows no programming option.
I connected...
Trying to integrate the serial part of the example code for use with a custom nRF52840 board. The problem is that I'm getting an error in uart_callback_set(uart, uart_cb,...
I use `west debug` to start `gdb` for debugging nRF5340DK
when I use `west build` to update the image, I use `load` command inside gdb CLI, the new `zephyr.elf` is loaded...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
Hello,
I'm working on a BLE central multilink application, where I want to get the list of all peripherals in range, In order to let the user select the needed periherals...
I implemented UART communication as follows, but occasionally the same data is sent twice.
Enter the critical region (app_util_critical_region_enter).
Store the transmission...
hello!
I'm using 'NRFX_LOG_INFO' for debugging purposes. However, the code seems to stop progressing when 'the NRFX_LOG_INFO' statement is removed from the section below...
Hi,
I am using an nRF52 DK board to perform some very simple tests. All I need to do is receive a line of text over serial, perform some calculations and return another...
HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
For my application I need the UART TX/RX pins pulled low until I am ready to turn on the UART. Is there a method in Zephyr to do this? Currently when Zephyr starts it reads...
I saw some similar question, but none is what I am experiencing.
I notice some weird behavior while testing DMA mode, so I made a simple setup:
I set the DMA buffer to...
