Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Dear Nordic Engineers
I encounter a issue about gpiote channel() function of NCS 2.0.0.
I use gpio_nrfx_pin_configurationl() to judg gpiote channel is be occupied.
It...
Hi,
Iam using UART Driver Sample — Zephyr Project Documentation (nordicsemi.com)
Where to change the UART TX Rx Pin in the UART Driver Sample(echo bot) program in nRF...
Hello,
I want to define SPI outputs as highdrive outputs in a overlay file.
I know how to do this in the code:
But I want to do this in this overlay file:
How...
Hello,
We are using nRF52833 Soc and s140 soft device for our project. Application is scanning our proprietary Tags. We have Bootloader as well to support DFU.
Due...
I'm currently doing some research for a project and intend to use nRF5340 Audio DKs and the Audio Application. I need access to the LC3 repository to build the application...
Hi,
My Homekit project is based on v1.9.1 NCS.
with CONFIGs: CONFIG_DATE_TIME=y CONFIG_DATE_TIME_MODEM=n CONFIG_DATE_TIME_NTP=n
I use our iOS app to sync the current...
Hi guys. I am using nRF52840. Currently, I want to read out an image from a camera. The camera PCLK is toggled at 500Khz, and what I want to do is to trigger an interrupt...
We just recently started testing with slave latency above 0 to save power. Our connection interval is 60. If we have a slave latency above 3, then the connection terminates...
Hello,
I want to calculate RSSI using TX power(Measured power at 1m) and instant RSSI getting in NRF CONNECT APP and Environmental factor.
I have used this
Distance...
I want to debug my adafruit feather nrf52840 sense with my nRf52840dk I followed this link: FAQs | Bluefruit nRF52 Feather Learning Guide | Adafruit Learning System
But...
Hi,
I am having a connectivity problem with a central Bluetooth device (nrf52832) that has to be connected to a peripheral (nrf52840), previously this connectivity worked...
I had a simple blinky application. With this application running I was able to flash a new version in the nRF52480 SDK board at address 0x0086000 with JFLASH. Pressing button...
Hi,
When sending a command using Zigbee, I understand the best method to use is by using:
So when calling light_switch_send_step, I use:
Which in turn calls below...
