Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
Is there any way to tell when the modem has finished doing a band scan? I would like to know so I can swap between CAT-M1 and NB-IoT for globally deployed devices. ...
Dear
I am try to perform an OTA operation on a dongle of nrf52840 by ble_app_blinky for PCA10059 project and light-switch server for PCA10059 project, which works well on...
I've setup SDK 1.4 with Segger, however I can't get the Asset tracker Application to compile. It seems to be building the SPM even though the project is setup to use the Non...
I use the template for pairing and binding. For the first time, after binding, for the second time, I bind again, prompting to reject binding. How can I match and bind many...
Hi,
I want to compile and run Mesh examples. I tried the Light Switch client, server and the Sensor server examples. All of them fail when the linker is invoked. All of...
Hi everyone!
I'm new in Nordic DKs and I have a new Nordic Thingy 91, I understand that it uses two chips: nRF9160 and nRF52840.
Maybe this is a silly question but, can...
I have a custom beacon application that is mostly idle. Before adding a timer, the current consumption was 3.2uA. After adding the timer, the current consumption jumped to...
So far I've use the nrf gatt module for setting MTU and DLE and seems to be working, however this module does abstract packets and maximum tx time in a connection. There are...
I have incorporated the DTM example into my application. It works as expected when I set the NRF_POWER->GPREGRET and then perform a reset sd_nvic_SystemReset() , then enter...
Hi,
https://devzone.nordicsemi.com/f/nordic-q-a/67024/nrf9160-questions-related-to-immutable-mcuboot-application
From the above thread i learn that MCUBoot is not that...
To get the GPIO binding I can use:
device_get_binding("GPIO_0");
1. I would like to know where in the documentation it lists the strings you can pass to that function...
I am debugging the GPS function and referring to the sample code of the official GPS. As for the code of reading GPS data, I have a question that is the way of obtaining GPS...
Hi,
We are facing some issues between our ble devices (ble version 5) and android mobiles using nrfsdk ("Android-BLE-Library") library. (Version 2.2)
We are able to connect...
I have used two sample applications light / light_switch from bluetooth mesh to get a device with 2 elements:
- generic on/off clent
- generic on/off server
I want to...
Dear Sir,
The target has a non-secure bootloader on it, I'm trying for DFU which has a secure bootloader pkg only. After initiating the DFU, nrf connect app sends successfully...
