Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I have been trying to use the new GPS example, however, I could not get any location from it yet. It seems that after 30 tries, it stops working (time-out problem). Should...
Hi all,
I'm starting developping code with SES, on an nRF52810 (192kB of Flash), with the BLE stack S112.
Because my project include BLE and custom UUID, I started with...
Hi
I am using the nrf53832 dk.
In the nus example once the data is received from the phone(central) I want to write this data to the flash. I referred to the fstorage...
Hi everyone,
We are currently working on a BLE border router with a module based on nrf52840. The custom board has a MAC + PHY ethernet controller that communicates with...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through below...
Hi everyone,
I completed tutorials and i tried to get a value from characteristic and i tried to do something extra. But i am encountering a problem which i could't understand...
hello.
My first nRF9160DK is 0.8.2 2018.49 and all demos goes well on it.
My second nRF9160DK is 0.8.3 2019.1 but none demos goes well on it except at_client.
Is there...
Dear all,
I want to know the methods to analyze Bluetooth 5 protocol, such that these packets sniffer tools: BLE USB Dongle from TI or nRF52832 DK.
Which one is better...
android OS: 6.0.1
nRF Connect: 4.22.3
nRF5 SDK: 15.2.0
Hello
With the nRF Connect For Desktop and also with the app on iOS, it works perfectly to perform buttonless...
Hello,
I understand reading your documentation that the nrf5x series have support for RPL but i can't find the implementation in the SDK 15.3.0.
Is RPL implemented in...
I am working on a project to do serial uart dfu in nrf52810. For that purpose i will be writing c code equivalent to nrfutil. I was going through all documentation and tried...
Hi, guys. I'm using PCA10056 and SDK 15.3's BLE UART peripheral example.
I also have a Microsoft HoloLens (the first version which runs Windows 10 and the HoloLens shell...
Hello
I am working with LIS2Dh12 accelerometer sensor interfaced with SPI 2 of nrf52832. For its one of the axis we have configured the interrupt which is working fine individually...
hi,i am using nrf52 DK kit. i have interfaced it with bmd 101 ecg sensor. The sensor sends continuous data over UART. I am using SEGGER IDE. The code which i am using is ble_app_uart...
