Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi, I'm currently in trouble with the sd_flash_write function. I've already a library using this function running on the nRF52832 with the S132 softdevice. But when a tries...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
Hey,
I'm trying to put the nRF9160 into System Off mode and am getting a bus fault error when writing to the REGULATORS module. This is the error output:
***** BUS...
Hello everyone,
I try to import a project from Keil to SES,
I 'v read the instructions in this article.
Segger Embedded Studio - A Cross Platform IDE
Generally I have...
HI:
I'm using a cli routine from the SDK，and I register the callback function zcl_device_cb() with ZB_ZCL_REGISTER_DEVICE_CB()，But whatever message I receive does not go...
Hello community,
I successfully flashed assets_tracker code into board and configure in NB-IoT using Configure NRF SDK project in segger studio.
I used Vodafone SIM card...
Hi, I use nrf52832's uart with a simple driver, not "nrf_drv_uart", because I don't know how to use receive and transmit interruption with "nrf_drv_uart". the uart drive i...
Is there a supported way of doing an unsecure flash (the nRF is hardwired via UART to a secure processor) without rebooting?
The HW design the nRF is integrated with uses...
I am using the nRF52840 DK to read data from an IMU sensor (STm LSM9DS1 9DOF). Like most sensors, you transmit the register number first (on MOSI), then continue clocking...
Hi,
I am trying to develop models using the Specifications. I came across generic battery model which was using 24-bit values, time model which was using 15-bit and 40-bit...
Hi,
I've modified the SDCard example to write every 2 seconds 80 bytes to a SD Card. The SDCard is correctly mounted and the File is opened and kept open.
After several...
Hi,
Sorry if my english isn't perfect but I have a quick question and I could't find a good answer for what I'm looking for. I'm using a FPGA Arty S7 as a SPI master and...
Hello Nordic team
I have tested individual "record text" NFC example and buttonless dfu example with SDKv-15 and both example are working. Now I am trying to merge both...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hello Nordic Semiconductor Team,
I have a device which uses the buttonless dfu bootloader / app design. And now i have some issues with updating the firmware with iphones...
