Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi ,
I'm working on a 2.4GHz wireless microphone project now.
I want to make a scheme of two microphones transmitting to a single receiver(2T1R)。And ,i have tested this...
Hi, Andreas.
Following the guide you find in the document " Buttonless Secure DFU Service ", I get errors while trying to compile. In order to ascertain were is the problem...
How to realize the USB HID interface and PC data transmission?
I want to connect my computer via USB hid protocol for communication
This is my code, but can only send...
Hi everyone,
I am a beginner for BLE software development with MDK-LiteV 5.26.2.0.
Target device: nRF52832（EKSHCNZWZ made by Taiyo Yuden）
SDK: nrf5_SDK_15.2.0_9412b96...
I use the example from nrf51422 ble_app_uart_c with SDK_12.3.0 to connect via BLE to nrf52 usbd_ble_uart. When sending data that exceeds the length of one BLE packet (for...
I combined to examples from the examples library combining the sdk_config, source code, and adding references to the included files.
The application will not compile and...
Hello
I am trying to send data every 5 seconds from a temperature sensor (MAX30205) using the nrf52 chip to a mobile phone via bluetooth.
To do this, I have studied and...
Hello - EVERYONE...!!!
I would like - please...??? please...??? for someone to help me... with a software development task..
this task is simple to the VERY CLEVER ABLE...
I'm using SDK 12.3.0 with nRF51 in SEGGER ES. I stumped upon NRF_LOG_ERROR problems. Digging it down i needed to find NRF_LOG_INIT. It was defined in nrf_log_ctrl.h like that...
Hi,
Is it possible to add SD card (either SPI or MMC mode) to nRF9160-SiP?
Hoping since the SiP is powered by Zephyr-OS, that should be possible.
Please advise. Thanks...
Hi,
I just bought the nRF52840 dongle and I wanted to connect it via bluetooth to the nRF52832 board. Is this possible? or will it only connect to the nRF52840 board (PCA10059...
I've been using the nRF52840 dongles with a J-Link Plus for over a year now - they generally work great. I am using them without the mbed bootloader, and programming/debugging...
