Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello, we have developed our product with S132 version 6.0.0 and sdk 15.0.0 since that was the most current when we were in the development stage.
However, now we need the...
When switching the dongle into DFU mode, it changes the serial port number when running in windows.
Both the bootloader and the application sets up the USB and calls the...
Hello, I am using the nRF51422 development kit. The SDK I am using is the nRF5_12.3.0_d7731ad. I am trying to run the "Blinky" example by copying the hex file for the PCA10028...
Dear Nordic Team,
we are developing a system with Bluetooth Low Energy and Zigbee capabilities (using the TI CC2630 microcontroller as Zigbee external communication device...
Hi,
In our project we have got one NRF52 as a central and one as a peripheral.
For now we are correctly connecting between our devices - periph is advertising and central...
Hi, I was wondering if there was an updated example for using the Flash Manager correctly with SDK for Mesh v3.1.0?
Some info about my setup:
Up until now I have been...
I am bringing up a breakout board for an nRF52832 module (MDBT42Q) and can not get a response from the module. The breakout board has very little circuitry, mostly fanout...
The AES tests for the CC310 cryptocell backend seem to only use the 128 bit key length.
While ECDF seems to support bigger key sizes (192, 256) AES does not.
Is this a...
I can update firmware in my nRF52 nodes using DFU where on the other end I have Android phone or nRF Connect (PC/Windows)+PCA10040. Everything works fine. But in my application...
Hi,
I read so many articles but just can't find the correct way to add twi support to the ble_app_hrs_feertos app in the latest SDK15.
This what did:
- Copied 3 lines...
Hello
I am adapting some code that was used with a previous SDK (SDK 14 or earlier) to use with SDK 15.2.
The function 'ble_nus_string_send' is not included in the new...
Hi support team,
I am porting an ESB application from nRF51822 to nRF52832.
I have configured (for backwards compatibility) the radio at NRF_ESB_BITRATE_250KBPS and it...
Hello, this is Kwonjoon Lee from Korea. I would like to ask about building problem of connectivity HEX file of pc-ble-driver (C/C++).
Actually, installation of the pc-ble...
SDK - nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac
Segger embedeed studio
Linux Ubuntu 18.04
I try use the thread_simple_coap_client example from SDK. I need to use...
hi,
We are using nordic nRF52832 in our project as per our requirement we have to implement sleep and wake up mode with the help of button interrupt. our use case is that...
