Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
First some general info:
* Compiler GCC 7.2.0 GDB 8.0.1
* VisualGDB 5.3R8 Build 1973
* Visual Studio 2017
* SDK 12.0
I try to build an application using the SPI...
I can play with at client and asset tracker demo with my SIM card but I don't know the network type of my SIM card. Can anyone tell me how to determine Cat-M1 or Cat-NB1 or...
Hi,
I am using S130 on an nRF51822 with SDK v12.3. I want to handle the different error codes that could result from calling sd_ble_gatts_hvx and retry later.
Firstly...
Hi,
we've developed and produced a nRF52832-based custom PCB with custom firmware that is using advertising, scan, connection, custom Bluetooth service and characteristics...
Hi there,
I am designing my own custom nrf52832 PCB and would like to have my design evaluated before put it to production. I am just wondering if Nordic Semiconductor provides...
I am running SDK 15.2 on an nRF52840. I have programmed my secure dfu bootloader, application, settings.hex, and softdevice via jtag. During the first run after programming...
Dear fellow developper,
I'm trying to create a BLE device using HID service to control music, volume and so on.
I have successfully implemented a keyboard + Consumer...
Hello,
I would like to know if anyone else has faced this issue. Indeed, if i want all the consumer control interpreted in the right way, i need to add a keyboard in my...
I'm working on a project with nrf52840 and i'm trying to send and receive ipv6 packet throw thread protocol so i tried to use to send with otIp6Send and receive with otIp6SetReceiveCallback...
Hi,
We are currently working on a project involving a few Connectionless BLE advertisement transmitters based on nRF52832 (SoftDevice 6.1.0). On the receiving end we have...
Hello
I m hardware designing engineer in Turkey.
I m designing bluetooth controlled lighting armature. it must be connect other lamps. And must controlled by phone ios...
Hello all,
I got the nRF52832 dev kit and have been playing around with it. I am using Segger Embedded Studio V4.12. I tried out the ble_app_uart and the writable_ndef_msg...
Hello! I used the "blinky_rtc_freertos" example and transferred ticksource from RTC to SYSTICK in "FreeRTOSConfig.h". The application has stopped working. What am I doing...
