Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I have some doubts about bonding,the parameter about PM_PEER_ID_N_AVAILABLE_IDS and...
Hi, latest SDK15. Running BLE_UART example on devkit evaluation board.
Budget Lenovo Android phone will discover BLE device.
iPhone X will not discover BLE device...
How to configure a node for control model. I have used light switch on/off template to implement a control mode but i i don't know how to make a control logic for client....
Let me preface by saying I'm pretty new to working at this low of a level. I'm running a pretty simple program that is toggling a pair of pins once every half second. The...
Hi,
I'm using SDK 15.2.0
I need to measure the voltage in AIN3 and I would like ot know what is the difference between ADC SAADC and SAADC legacy layer.
The system...
Hi,
I am trying to set up SEGGER Embedded Studio for ARM and run secure_boot project.
All the time I have "Project load failed Reported error: solution load command failed...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52. And I am using Segger Embedded Studio to build and debug the code. But the IDE is unable to find the libraries...
Hello Everyone,
I am using nRF52832 with Softdevice S132 v5.0 and SDK 14.2.
I have been using ble_app_uart application as a starting point with SES. What i need now is...
Hi all,
I'm trying to learn more about the pairing and bonding procedures in the SDK. I connected one nRF52480 DK to my computer (running Ubuntu 16.04) and let nRF Connect...
Hi everyone, I have a nrf51822 Bluetooth chip that control a stepper motor, this Bluetooth chip can be powered by a maximum voltage of 3.6V, but I need a higher voltage for...
I have a split bluetooth keyboard that is using this firmware for the nrf51822 chips: github.com/.../mitosis-bluetooth
The general idea of the software is that the right...
Hi,
I am following the application note nAN-15 in which it mentions I will have to download NRF Probe and install but for some reason I couldnt able to find the software...
We're reading RESETREAS at startup from our nRF52832 cpu, and getting the value 10. The docs show that this refers to DOG and LOCKUP bits both being set. We don't have the...
Hello,
i'm using the nrf52832 with s132 and SDK15. I start the project take into account the example ble_app_hrs_rscs_relay.
The system is composed by 3 different services...
