Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Dear Colleagues,
I am not sure whether TEMP anomaly 31 is applicable to nRF52832-QFAA-0B (NRF_FICR->INFO.VARIANT == 0x41414230)
nrf_temp.h @ 65 says:
static __INLINE...
A happy new year everyone,
I should develop a mesh sensor network for Raytheon Anschütz GmbH in Germany but I am an absolute beginner on Zigbee and therefore struggle a...
I have a BLE project that I wish to add Zigbee to (non-concurrent, if that matters). The project is built on FreeRTOS with several threads, using SDK 5.2.0 and S140 6.1.1...
Hi,
I am using nRF52840-DK evaluation for testing a Mesh configuration. I was able to successfully establish a mesh connection with a onoff-sample from zephyr and was able...
I am working on the project with radio transmitter(NRF24L01+) and receiver(NRF52840). I need to receive data at the rate of 250kbs. I tried to receive but it fails always...
Hello,
I want to interface a microcontroller with the nRF52832 chip in one of our designs. The microcontroller will be running on FreeRTOS.
I would like to know a few...
Hi,
We are currently in a testing phase of our software where we use an nRF52832 for extended advertising and an nRF52840 for scanning that has a scan interval and scan...
Hello, i´m trying make DFU with the Light switch server with the GATT and Proxy Enable, however in the process of update, i got this error in the device what receive the update...
Trying to lower uC current consumption to minimum
Im trying to remove features from my program
I've notice that removing the adc initialization actually get the current...
Hi All
I mount a minimum system for test BLE. I download a blinky program to the NRF52810. If I download a blinky without BLE version , it works well . But if I download...
Hi dear Nordic engineers and enthusiasts,
I am currently testing and researching on the functionalities of Nordic Thingy 52 in Bluetooth Mesh . I have tested with the provided...
Hi
I am trying to use the TWI on nrf52840 but i am unable to get it to work. its getting stuck somewhere. I dont have a logic analyzer so i am unable to check if the signal...
Hi,
I'm doing some experimental evaluation of BLE Long Range. I use the ble_app_att_mtu_throughput example with parameters:
ATT MTU: 247 bytes
Data length extension...
I am trying to test out the whitelist that I have created for the nrf52832 client. I have edited the whitelist so it will only allow one device to be bonded and added to the...
