hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
I'm trying to integrate buttonless DFU in BLE app uart example. I added the file: ble_dfu.c, ble_dfu_bonded.c, ble_dfu_unbonded.c in the project. I added the following folder...
It's battery operation so I want to know how to setup 1sec timer and goto sleep_mode(power_down) after 1sec beacon scanning.
I'm using WDT to setup 60sec WDT reset so I...
Hi,
May I know what is the hardware layout for measuring external voltage using SAADC? I may not be understanding the infocenter or the datasheet for setting the external...
In the `Serial Interface`, the `Bluetooth Mesh Packet Send` command does allow specifying the `Time To Live` (TTL) for arbitrary packets, but there is no field for `Retransmit...
Hello, I have a question.
1. When ancs is reconnected, the machine will be reset, and the software will catch the log as follows.
As long as there are a large number of...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to know what would happen in the following situation.
During central and peripheral...
I noticed that in SDK SES projects, the linker file is generated every time the project is build. However, there is no memory map file specified, only a section placement...
I program in nrf52840 using thingy sdk
I succeeded in receiving the motion service.
The output speed of some motion services is too fast. such as raw, heading, gravity...
Greetings!
I'm new in the Nordic Dev Zone, so I apologize if this has been asked before. I just wasn't able to find a satisfying answer.
I read in this foruns that there...
dear
i am using this proj to get dfu functional
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main.c
i add some code in main.c...
Hi all,
I want to see the value of the radio registers, especially the Tx power register, but i can see only the cpu registers in the register window.
I'm using segger...
