Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi Guys,
I'm interested to get guideline on how could I customized the qspi example from nordic in terms of pins and command. I don't see any different between MX25R6435F...
The NRF_MODULE_ENABLED macro does not play well with Eclipse. I've tried enabling all Modules in the Symbols section of Eclipse but still it does not enable any module utlizing...
Hello all,
Anybody knows "EVENT_STARTED does not fire" issue will be fix or not?
I really do want to use the PPI function at Tacq=3us.
When can I get the counter measure...
Hi,
I am trying to use EasyDMA. Is it preferable to use with ...\peripheral\uart or ... \peripheral\serial. With ...\peripheral\uart there are lot of errors. I tried with...
In the code above I get an error that nrdx_gpiote_in_init() and nrfx_gpiote_in_event_enable() are undefined.
In CMSIS configuration wizard -> nRF_Drivers i've enabled...
Hello everyone, i work on nRF24L01 and i have 3 ardunio with 3 nRF24L01 and 3 IMU as transmitter and 1 ardunio with 1 nRF24L01 as reciever, i am trying to recieve data from...
I have migrated a project that uses Thread DFU from SDK for Thread and Zigbee 1.0.0 to 2.0.0.
I have successfully loaded the new MBR, bootloader, settings and program via...
Not sure where the problem is. Some of my boards, the microphone works fine, on others it doesn't. I am using a Knowles SPK0641HT4H-1 PDM microphone. I am using it as mono...
Hi,
I am experiencing an error of up to 8% on SAADC readings on the NRF52832. We have performed a sweep of the full range of the ADC and produced the following graph which...
Hi
My application requires that SPI CS is NOT TOGGLED within a transaction, only at either side
My Transaction consists of:
1 - Slave sets up buffer ready for Rx and...
we are entertaining the idea of using an nRF52840 with a Semtech SX1276 (or possibly SX1262) as a BLE/LoRa endpoint node. We believe this is doable but wanted to make sure...
Hello, I am using SDK15.2 on nrf52 DK with SD 6.1.0 and having an issue while sending back to back data using NUS service. I have edited the ble_app_uart application and trying...
