I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
I was wondering if the SPI configuration for the p_config->sck_pin is correct. It appears that the clock is configured as output with input connected. Wouldn't this...
I am searching for long time how to inspect the prints in my code inside Segger , I went over many messages in this forum and nothing comes easy to me with this Segger thing...
Using Segger , only the BLE template is advertising,All other BLE apps such as BLE_UART, will flash the leds very fast but will not show on any Apple device on the Bluetooth...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
Hi All,
I have developed an application on the RedBear BLE Nano2, and am trying to port it accross to a custom nRF52 board.
The Hex that the Arduino IDE outputs does...
I have an application which requires protection from passive eavesdropping, but not man in the middle attacks. I want to enforce the use of diffie hellman key exchange.
...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
