When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
How do I use hardware crypto on a nRF9160dk? I am using the nRF connect SDK and my build is nrf9160dk_nrf9160_ns.
Would that be cryptocell or something else? If it's cryptocell...
I am using nRF52833 / NCS 2.8.0. I'm using Gazell Pairing, but I only need pairing, not encryption. So I'm only using unencrypted pipes. If it is a non-encrypted pipe, it...
Hi,
In my design, I have a push-button that pulls low when pressed and remains floating otherwise. This button is used to wake the nRF52832 from system off mode.
The push...
Hello nordic:
May I ask about the requirement of 32M OSC of 52832 ?
EX:
Frequency tolerance
Equivalent resistance
Loading capacitance
shunt capacitance
Drive...
Hello Nordic team,
I am working on MCU nRF5340 and NCS v2.6.0 for BLE secure pairing level 4 with adding LTK (Long Term Key) share support. But, I am unable to find the...
Hi, I am currently designing the schematic for nRF24L01+ module interface with arduino nano atmega 328p MCU. Due to inventory restrictions and the current soldering capacity...
I have the SH6MDBT50Q BLE module, and I need the nRF SDK to implement a Bluetooth Mesh connection for transmitting and receiving data on both sides. I am using Segger Embedded...
Hello, Nordic team.
We are using two nrf52833 DK boards to build an ESB master-slave communication link. We are debugging the example program based on the nRF5_SDK_17.1...
Hello Nordic Team, We have a customer using the NRF52810-CAAA package, and they need to enable the DCDC. However, due to PCB size constraints, they hope to replace the 10uH...
Hi Nordic FAE, Merry Christmas:
We are using nRF5340 with nRF Connect SDK V2.6.1 running on Zephyr OS.
Do you have the nRF5340 power management guideline document?
Function...
Almost all of our carrier frequencies have the offset of 118KHz. How can I tune it in the software beside changing the capacitor?
I have gone through and
Hello Forum,
I have been trying to get printk/logging to work on the NRF53 audio DK for days now.
I have tried a bunch of apps including hello world from the zephyr 2...
background:
1: my board is the same with the nRF52832-CIAA Reference Layout 1_0 from nordic docs.
2: the source code is from sample code: blinky_led
3: only change the...
