Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi, I am programming a commissioner through Openthread's API on the older thread and zigbee SDK and I can't seem to get it up and running. No matter what I try I seem to get...
Hi,
I am using an external low speed clock driven rtc to implement the perpetual calendar feature, but when setting the time, I find that the COUNTER is not modifiable....
Hello, acording to the Simultaneous multi-image DFU documentation a RAM section is needed to act as a flash simulator during the network core update.
Is this RAM section...
Hi
I have seen that IP DECT and DECT NR+ use the same frequency band in EU (1880-1900 MHz). Will setting up a NR+ system in the same place as IP DECT degrade the performance...
Hi,
I have integrated SPIM interface using the default QSPI pins and have received 16MHz speed.
I would like to evaluate the high speed SPIM that runs at 32MHz for my...
I am trying to build example code ble_app_buttonless_dfu with some modifications. I was getting this error. Tried to clean and build, it's not working I have attached flash...
When I am using the NCS SDK v2.6.1, I am confused
1.How to get the time of each AD packet sent?
2.Is there any way to record the time in the AD packet?
3.There is a...
Hello,
i am new here.
i am just looking for a reference where can i find all registers and their description of nRF52832 - PCA10040 ( user manual )
can some one help...
We have a project on a 5340 based system, that only occasionally needs to have Bluetooth running. We have a relatively small battery in the device, and want to save every...
Hello, On nRF Connect for VS Code extension v2024.9.87 and v2024.9.31 , a USB connected J-Link probe (Segger Edu Mini) no longer appears under "Connected Devices".
J-link...
I have a nRF52840-DK that I know that it has a JLink on board, but the RAK4631 don´t have JLink, then I am following the RAKWireless bootloader update( Bootloader update ...
Hi everyone,
I'm currently developing an application supposed to read through SPI from an extrernal SRAM, i'm using nrfx_spim libraries.
Compilation is flawless but when...
Settings document explain .h_set handle will be called when the value is loaded from persisted storage with settings_load().And I want to know how it work.
I put a breakpoint...
The Bluetooth connection is disconnected, but no disconnect message is printed, and no more ads can be searched, the main thread is running fine, and the Bluetooth function...
