Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello, guys.
I have nRF51822 SoC running Zephyr OS. Among the other things, the nRF should communicate (over I2C) with the touch controller that will fire an interrupt every...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am a beginner at Nordic. I want to understand how I can access a pin named " P1.04 ...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
I am working with nRF connect SDK with nRF52840 dongle. I am compiling code using nRF coonect for VS code with nrf52840dongle_nrf52840 board.
For Programming nRF52840 dongle...
Hi
I have similar question to the post https://devzone.nordicsemi.com/f/nordic-q-a/7013/nrf51822-internal-ldo-output-pin .
I need a stable voltage to elevate the reference...
Hello everyone,
I use the multirole software as base for my application and I programmed everything with a evaluation board. I design my own PCB and decided to not use the...
Hi,
Is there any sample in nRF_Connect_SDK that implements RTC on nrf52840 SoC?
I need to implement RTC in my application, so is there any example reference for this...
Hello,
I am trying to set the `BT_SHELL_NUS` project up as a standalone repository. My requirements for this are as follows: I only want to commit application code to git...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We had to change the SDK version to 1.9.1 from...
I am trying to implement RSA signing into my application, I am planning to use the following example as a starting point but the sample, with no modification appears to not...
Hi there,
We are developing on the NRF5340, and have a question regarding the drive strength that can be set on a GPIO pin using the PIN_CNF register.
However we can not...
Hello,
i am using the nrf52810, ble_app_template example to read Accelerometer and gyro-meter data from ICM42605 sensor. so i have followed the i2c communication tutorial...
Hi there,
We are not able to find the reset due to brownout within the RESET->RESETREAS register? Is this the case? There are explanations of the brownout detection in the...
I'm trying to get DFU working with LPN on the 833. The sequence I follow is: (Erase board) Flash Soft Device Flash Bootloader (Using mesh, but don't want serial)
Flash Device...
Hi,
I'm trying to setup a very basic network based on the thread CLI example.
I have an nrf52840-dk as a router/commissioner and a custom device as a nrf52840 joiner...
