I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I am trying to change the curvetype of the ecdh example from NIST secp256r1 to Curve25519 or Koblitz secp256k1.
To achieve this I enabeled Koblitz curve secp256k1 and Curve25519...
Hello Devzone,
Our research group is using the NRF52832 chip embedded in a flexible substrate to transmit EMG (muscle) signals via Bluetooth. We’ve been having a couple...
I have been trying to find a solution for this but to no avail. I have nrf connect 3.10 installed. I am trying to flash my compiled code but keep getting the error: Unsupported...
In general, it's not a question, but the only suggestion for SDK developers how to improve debugging way.
So, while implementing DFU upgrade in my project I faced to the...
Hello everybody,
My project is based ble_app_eddystone example and nRF5_SDK_17.2.0 SOC is nRF52832.
Beacon advertise Eddystone UID +Eddystone TLM +Eddystone URL, works...
Dear,
how to change the adv. timeout setting and disable uart0 and uart1 in ncs v1.6.1?
I use the nRF5340 and example peripheral_lbs.
The path is as below:
nrf\samples...
I am using the following CAF modules on nRF52840DK, ncs 1.9.1: Buttons, LEDs and Power manager (see attached project caf.zip)
Button 1 is used for ON/OFF fuctionality. When...
I submitted a project idea for the Electromaker make it smart thingy:91 contest. Part of that was to detect and alert a user if there was an impact. This would require access...
How do I find out which peripherals are available at the same time?
Somewhere it was mentioned, that peripherals wit the same "ID" are on the same HW and only one of them...
Hi,
What's the max range achieved with BL5340 (With PCB Trace antenna) in indoors and Outdoors when advertising and connected mode? (With 1M,2M and Coded PHY(125Kbps,...
I use nrf connect sdk 1.9.0, to run periodic_adv and periodic_sync example.
The adv side sends this data: mfg_data[] = { 0xff, 0xff, 0x00 };
But in sync side in scan_recv...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
