why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I'm trying toa custom nRF52840 board using SDK 17.02 and SD 7.01
I create a read/Write only service, it shows up in nRF Connect just fine
I can write to the service using...
Good day,
1. I am running the Asset Tracker v2 app on my nRF9160DK and I am monitoring the battery voltage and its time stamp from my nRF9160DK, as this data is transmitted...
In the Matter documentation, under the topic Building Matter - > Getting Help , the "Also see the quick start guide" link is broken. For me it gives:
NOT_FOUND: Requested...
Hello,
I am trying to use googleapis.com to perform cell and wifi geolocation and am having trouble connecting.
I am using a custom board with a nRF9160 chip and the 1...
In the below picture, it says Thingy 91 is certified for the bands given below.
Can you please confirm if this board is certified for AT&T , Verizon?
Regards ...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
I had described my problem in my previous question .
In short, after a long time of a bunch of central BLE devices regularly connecting and disconnecting to my nRF52840...
I've did my homework and googling but got more confused than ever.
Basically I'm trying to printf to the debug (printf) viwer window to help me demonstrate certain information...
Hi Everyone,
Hope you all are doing well.
I'm using nrfConnect sdk v1.7.0 and vscode for development.
controller : nrf52833
Here I tried to build image with bluetooth...
Hi. I have been using this document to work on the Fanstel USB840F device. USB840F_User_Manual (squarespace.com) After erasing the device, I could'nt run this below command...
Hello, I am developing a custom board using the nRF52810 WLCSP package. I realized I made an error in the board layout after placing my order, the error being that I placed...
I made a DFU Bootloader for my nrf51822 that waits for two seconds before starting the application, so I have time to connect and flash.
That process was working with the...
If I set two separate UUID scan filters as below:
Is it possible to discern which event triggered the filter match?
At the moment on the scan_filter_match callback,...
