hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi , I want to send a char data through bleutouth using ble nus I am using this method
I don't have any error but I don't receive any information on my android application...
I am using nRF Connect for Android and had a question about a script I would like to develop: for this script, I would like user input to specify part of the value I write...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
I am trying to figure out how to use the SAADC component of the nRF52840 to measure an analogue input and report it as an attribute in a Zigbee end device. I have, so far...
Hello,
I am analyzing the DKs power amplifier characteristics as an assignment for university. I got the serial_lte_modem running and send AT commands via UART from an external...
Hi,
I am looking for a 4G module with in built gps in it. It has to work in european market, need to have esim facility.
Can you provide with the product links.
-
...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
