Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Excuse me:
The SPIS example in SDK is shown in the figure below,the m_rx_buf buffer has only seven bytes，Does NRF_DRV_SPIS_XFER_DONE event occur when the buffer is full...
I am developing a NRF52810 product, I am downloading using JTAK on NRF52832 development board.
I have the NRF52810 because of the lack of IO pins. SPI CLK , TWI CLK are...
I use the NRF Mesh SDK v2.2.0
- EVB PCA10040 burn the serial example
- EVB PCA10056 burn the light server example
- PCA10040 attach to the Raspberry Pi 3 via USB for...
I'm trying to follow these instructions to update the openthread binaries in nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
I have a Windows host machine and a Ubuntu VM...
Hi,
I am trying to do AGPS with the supl library. I obtained version 0.7 through the application and installed it (and enabled the required config options).
Unfortunately...
Hi Nordic,
I am working on project with nrf52840 , which is a central to connect other device. we will enter the MAC address to central, and setup the scaning filter.
...
Hi all,
I am trying to do bonded buttonless DFU but an error named NRF_ERROR_FORBIDDEN was raised in enter_bootloader() function under ble_dfu_bonded.c.
The description...
hi，
I currently have an application scenario，using a nRF52832(M board) BLE maser to upgrade another nRF52832(S board) is run standard DFU ，Are there any demo available？
Previously, I used SEGGER to build and run programs on nRF52 DK very quickly (5-20 seconds).
However, for nRF5340 DK, it usually takes about 8-15 min to build and run just...
Hi,
I am trying to connect the current product with MCU EFM32GG290F1024 to a Nordic BLE module in a serialization over UART.
I have port the SDK to my project and need...
1. hardware : nRf52840 dongle.
2. Purpose : Update Firmware into dongle to be sniffer, and restore original default manufacturer firmware for nRF Connect v2.6.0 desktop...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
