Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'm working on a project that has multiple custom partition manager configuration file that are implemented based on the instructions provided in this section of the partition...
Hi,
yesterday, I met the same situation as here . But now, I can't even see one log, even after I annotated the code related twi and just remained some “NRF_LOG_INFO（）”...
Hi,
I am using SDK 17.0.2 for a simple scanner project, where nordic SoC is communicating with main MCU via SPI. The code starts normally on nRF52832, but on nRF52833, it...
Hi,
I am running the example ble_app_att_mtu_throughput with the nRF5 SDK on two nRF52840-DK dev kits. I have flashed both dev kits with S140 soft devices prior to flashing...
We are finalizing a product that has a BL652 (nRF52832) in the main unit and a BL651 (nRF52810) in a remote control unit. We are trying to get our regulatory radio testing...
When I changed HFCLK from "64 MHz internal oscillator (HFINT)" to "64 MHz crystal oscillator (HFXO)", the power consumption when executing sd_app_evt_wait() became larger...
Hi,
We've created a FW image targeting a PCA10056 which consists of our application FW, the example secure DFU bootloader over USB, and the softdevice. Everything works...
I have the ws2812 example working with ncs v1.5 on board actinius_icarus_som
However, when I combine it with other code such as for a custom SPI device and udp comms it...
Hello,
I contact to you because a customer is interested on the RF System, part number nRF5340-QKAA-R, and they asked the following below;
"
Customer wondering if you...
I added FOTA_DOWNLOAD and MCU_BOOT to my project.Then I want to use http to download a file, and an EBADMSG error occurs at this time.
I reproduced this problem in the download_test...
We have an I2S implementation that I based on the example code, but using the nrfx driver. Audio plays fine, but after I call nrfx_i2s_stop, I first see that no next buffers...
I didn't change anything and compile the source file from github. But my thingy52 keeps flashing and stays in DFU mode after new app hexfile was burned in
https://github...
Hi.
I use ble_app_hrs example.
Environment is follows.
- PCA100040 , nRF52 DK
- nRF SDK v17.0.2
- Galaxy Note10 mobile Phone
Bonding process is always fail...
Hello,
I am developing with reference to "Light switch example".
And once the nodes are provisioned, the device acting as a provisioner is powered off in a warehouse...
