This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello,
I would like to use Nordic SDK libraries (currently I'm using SDK 17.0.2) to read and write on a FM24CL16B I2C F-RAM.
This device has the following writing workflow...
Hello,
I recently used GPIOTE Events to manage Digital state changes and this is awesome. I would like to perform similar thing but when a PIN goes under/above a given voltage...
Hello,
I'm running NUS sample from NCS SDK 1.5.0 on two nRF52840 PCBs. Central board is Taiyo Yuden module and peripheral is nRF52840-DK. I've added some lines to prj.conf...
I am looking for an example where I can enable UARTE0 and UARTE1 on the nRF52833 DK. I am using nRF5_SDK_17.0.2 with Keil uVision V5. I am successful with the loopback example...
Hi,
I'm new to building circuits with Nordic devices and am unsure about how to connect the MC3672 accelerometer: https://mcubemems.com/wp-content/uploads/2020/03/EV3672AB...
Hello,
We have been working on Nordic nRF52-DK board.
Board can be reachable by Bluetooth in the first 10 minutes of power supply. However after 10 minutes, we can...
Hi everyone ! I am working at a project. I dont't know which mcu was used this project but it was written for pca10040 and used s132. Many values are write to flash memory...
I merged in some of my code to the examples/thread/dfu/client in the v4.1.0 SDK for Thread and Zigbee. After getting OTA DFU working, I moved onto some commissioning related...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
