Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi Dev Team,
I am using the mqtt_simple example to publish my data out every 1 hour. I tried the example and it is working well and I was able to test it via MQTT.fx with...
Hi,
Is it somehow possible to plot data comming from external target board with nRF52, connected to nRF52 DK via swdio and swclk lines, by some data plotting program? Etc...
I am using NRF52832 for BLE application with softdevice 132 under SDK15.3. My application is supposed to sleep off after certain amount of time when there is no user activity...
I am using two SAADC channel on nRF52 DK, one for pressure sensor and another for battery level. I realized 0.5mA is higher than single channel. Is it normal?
We need to develop a portable device，In order to save cost and low power consumption.We need to know how to make nrf52832 connect to the Internet through the Bluetooth network...
I wrote a program to toggle the pins of P0 and P1.
When I write:
P0=0xff;
P1=0x00;
Only P0.0 - P0.3 are high and P0.4 - P0.7 and P1.0 - P1.6 are low.
P0=0x00;
...
Hello,
I am talking about nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c.
In the case of HEXDUMP there seems to be some inconsistency in the packet...
Just downloaded this (5.10d) on MacOS 10.15.7.
(Planning to test with 9160 DK.)
Using getting started assistant
Got as far as the "setup a project in SES" (installed...
This is our 4th nRF52840 DK this year that got damaged this way. After using it for 1 to 2 months the DK does not work power up normally. Then we can only use the board with...
In RADIO - 2.4 GHz radio TXPOWER register say:
"When the radio is operated on 1.2V, the output power is increased by 3 dBm, i.e. if the value -20 is specified, the output...
Hi,
We are having some EMI issues with USB full speed and would like to force the nRF52840 USB controller to operate in USB low speed mode. Is it possible to configure the...
Hi
I use the following script to program my boards which takes 20 to 30 seconds to complete. But recovery and programming done through SES for the same code is much faster...
I'm using nRF51 BLE dongle as a sniffer and trying to capture BLE packets through CLI. I'm using example.py which came with nRF sniffer software.
I unable to get the list...
