Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am currently using bluetooth mesh v2.1 which has qdid code QDID: 111537 , now we are currently added the Nodic uart service code, do i also have to declare the QDID 138862...
Hi, I want to create a peripheral device with a nRF52810 module.
Before developing the corresponding mobile app, I would like to use this as a central device: A GUI, written...
I have been trying to get a arduino UNO and arduino Leonardo to communicate with the nRF9160DK but have not been able. That accounts for the SPI example aswell as the I2C...
Given that Zephyr RTOS is not certified for use on Medical Devices, is there any plan to support operating systems with FDA 510(k), IEC 62304, IEC 60601 certifications?
...
I'm looking at augmenting the GPS system of the nRF9160 (at the moment due to high current and long time to acquire, easily lost sats/location) with some geolocation. Specifically...
I met a question here. Hope anybody can help on it, thanks.
I'm evaluating whether it is feasible to run the FFT algorithm on zephyr LTS project, with the nRF52832 board...
I want to know the upgradation process of firmware (Zephyr OS) on nordic nrf52840_pca10056. I have flashed the Zephyr OS on chip once via Jlink/JTAG, and now I want to flash...
Hello,
We are developing a product which includes qr code reading as its feature.with reference to https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo
as...
Dear All,
I need to develop a low-power application that sends a UDP message, waits for a certain amount of time (5 seconds) for a response and if there is no response it...
Hi,
Scenario : Scanning non mesh BLE packet with different stacks.
H/W Device - nRF52DK
Observation :
Case 1. Non Mesh BLE Stack (Soft device):: Here able to receive...
I'm working nrf52 DK, SDK V15.3 , S132 . I have created custom Services and characteristics its working fine. I need to change gap parameter in some cases because i need to...
Dear,
THINGY:91 / nRF91 DK
Currently, Power Saving Mode (PSM) is a feature that is not always available with roaming cards, and we must use the local sim card to use GPS...
It used to be downloadable, but now it's like this
The chip has the old code, and the chip can run the code
Is the chip's sdwio and sdwscl pins broken Or...
