Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I would like to know the best place to cut the power in switch off sequence.
We have a IO to totally cut power to the IC (own board), I added PIN control to switch off...
Hey,
I am currently using your product nRF52832 for RF Energy Harvesting applications. We need very low power consumption in sleep mode. In your user guide you mentioned...
Hello, when trying to finish provisioning my nodes (3 total, per example program's instructions), my provisioner program keeps running into
NRF_MESH_EVT_PROV_LINK_CLOSED...
i am using three boards , one is client (nrf52840) and other two boards as server(nRF52832) using light switch example . i want to get the message from client board ,to relay...
Hello,
I am having trouble understanding how the following function in the PWM driver example under peripherals in the SDK. Below is demo1 from the code that creates and...
I am not able to enter DFU Mode with secure bootloader example.
I use IAR and NRF Connect with Programmer to flash
Following are the steps I followed
1. Build Secure...
Hi Everyone,
In this code I'm face a problem. The issue is when i debug, it shows "<info> app: TWI device detected at address 0x6D" . Please find attached a snapshot of...
Hello,
I scrolled through some subjects about that SoC already but I wanted to get some more precision.
1. Can I start developing solutions for AoA / AoD system...
I am trying to do a ramping PWM. I want to update PWM every 25ms by increasing the duty cycle by 10%. I tried to setup a timer, by calling app_start_timer() on repeat mod...
Can you clarify how FLASH_SIZE, defined within the linker_section_placement_macros setting in the Segger Embedded Studio project file is used? Specifically: should it reflect...
In the light switch example, I try to change the network-key and then get some new unprovisioned servers provisioned.
The servers seem to get provisioned, but the client...
Hi,
I am working on NRF52840 preview DK using SDK version 15.3
I have compiled and loaded the Secure DFU bootloader onto the device, and also successfully got the BLE_BUTTONLESS_DFU...
I am using the mesh SDK version 2.2 (I think - I renamed the folder when I started, but I can't find a reference to the version number in the library! I am sure it is 2-point...
Hi,
How to calculate the free Ram and Flash after I loaded bootloader + SD + App on a running nRF52840?
I want to know ways to measure during critical RAM load too.
...
