Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
Hello everyone,
This is my first question ever, sorry voor my bad english.
Im just started to work with a STMF429I discovery board and a NRF52832(isp1507) BLE chip.
Im...
HI nordic
i installed command line tools in https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF5-Command-Line-Tools
and i got this exe file nRF5x-Command...
We have a custom board built around the nrf52840 chipset. We developed code against the dk kit of the same now we are trying to get this working on the custom board.
1)...
Hello,
So I need to connect my NRF52 with a LoRa module E32 via an UART connexion, and then I need to send data using this function:
The probleme is that my code work...
Hi!
I have found the following piece of code on an example from a Nordic employee. I'm curious as to its purpose.
Why is the register set, and then read just after...
I am testing BLE 5 throughput with the following hardware and firmware:
- two newly purchased nRF52840 DK boards, one as host and the other as peripheral.
- latest nRF5...
Hello,
I'm looking through the available packages in the SES Package Manager and I came across the captioned package - currently showing version 1.06 (no date). I haven...
...\sdk\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\multiprotocol\benchmark\zigbee
IDE: Segger Embedded Studio.
HW: Two 52840 DK, name them : A & B
PC Cli...
Hi
I'm using SDK 15.2.0 with Nrf52
I used the example of SPI from the SDK
..\..\nRF5_SDK_15.2.0_9412b96\examples\peripheral\spi
and I get this error
..\..\..\main...
Hi,
I use the SDK 12.3 ,example ：nRF5_SDK_12.3.0_d7731ad\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart
I want keep advertising，I use the code as follow...
I'm trying to configure an application queue to hold BLE events I receive from the SoftDevice. The SDK defines NRF_SDH_BLE_EVT_BUF_SIZE as the "Size of the buffer for a BLE...
