Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I have successfully implemented DFU over the Air function using Android-DFU-Library (Github) for my Android mobile phone.
The Android-DFU-Library needs Android 4.3+ at least...
Hi, I am after a bit of advice regarding the SPI interface between a nRF52832 acting as a master, and 3 slave devices. I only need to communicate with one SPI device at a...
Hello,
my goal is to measure the average current consumption of an external chip connected to the Power Profiler Kit on Windows 7. Since the Software inside the nRF Connect...
using SDK 12.1.0
The original error (compile time only) is
main.c(338): error: #94-D: the size of an array must be greater than zero
my snippet @ line 338:
SOFTDEVICE_HANDLER_INIT...
We run SR3 on android system which is working , need change system to embeded linux .
we run SR3 on embeded linux , i can't use voice function .
we get son info: https...
I wanted to use the sdk board support file with coustom board having 13 buttons. I have modified the bsp.c and configer number of low power events and added a coustom header...
Hi,
i have interfaced a ADC device in the nrf2 development kit,i am getting the values from the adc after using the SAADC example,
i want to implement the same with the...
Hi softdevice uses s130 The board is using nrf51 dk. The example uses the ble_app_beacon example from sdk12.3. if (switch_hit ()) { // NRF_POWER-> SYSTEMOFF = 1; // sd_power_system_off...
Hi Team,
Being trying to run the Thingy 52 mesh demo following : https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
I am using pre-built .hex file Thingy_node_s132...
Hi there,
Recently I bought an LTE module which uses a nRF52840 as the main processor to control the modem, I want to erase the flash for that module and flash the project...
Hello,
Recently I added TWI to my project it keeps a low consumption before call TWI functions to read or write after this my current consumption increases and keeps above...
I'm using the nRF BLE Mesh SDK 2.2.0 with SES v3.5 (64bit for Windows)
Our hardware with nRF52832 using internal RC
I'm running the light_switch_proxy_server but with...
Hello,
I'm just starting to use the nRF Smart Beacon kit.
Is it possible to have the beacon toggle a GPIO on-board when the beacon is out of range of the phone/app?
...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I want to ask how to use app timer with scheduler.
Here is my implementation. I just use APP_TIMER_APPSH_INIT...
