When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi Team,
My application is based on nrf51822 SoC in which I am using
BLE and UART interfaces.
There is single UART available and I have used it in communicating with...
Hello,
I am using am using sd_ble_evt_get and sd_app_evt_wait in an endless loop for handling all incoming events.
If I block this loop from executing, I'd expect that...
Hi all
I'm struggling with the easyDMA UART of nrf52. I've got a preview nrf52-DK here where I wanted to make a simple example with the following code but I never reach...
I'm doing a custom board with a nRF51822 FAAG0. I have in it the ST BAL-NRF01D3, with a 0.8pF capacitor.
In the forum I read in a post that some versions of the nRF51822...
Hi everyone,
I am using the nRF51 SDK 10.0.
The documentation for the Debug Logger API suggests sample code like:
uint32_t retval; // Initialize module
retval = app_trace_init...
I want to use the J-link to program the nRF51822 via SWDIO and SWDCLK, every time I click the
"nrf51 programming", the studio stops working immediately, PLZ help, thans
I'm trying to set up communication between an nrf51422, and an nrf24l01+.
The nrf51 is supposed to be the PTX device, and the nrf24 the PRX device.
Communication from PRX...
I was learning GPIOTE using the example provided in SDK 9.0.0. (examples\peripheral\gpiote). The example only uses GPIOTE task and a timer to drive the task through PPI. ...
We have created a firmware and encrypted it with a private key and made it public. When we download it to the chip it's decrypted with a public key stored in the chip. Right...
I have about 200-300 sensors, each requiring to send data at around 0.5-1Kbps to a central node (coordinator/master node), what will be the network configuration/topology...
In SDK 8 for the nrf51422, notifications are always being sent as 20 bytes, regardless of p_len. The BLE_EVT_TX_COMPLETE event stores the proper number in tx_length, but the...
Hi everybody.
I am making an application which combine ANCS and UART on PC100028 (nrf51 SDK 9.0.0). This program worked properly. However when I add DFU service (dfu_dual_bank...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
