Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
We are looking at using the Gazell protocol for a project. There isn't much information out there except for the "Gazell Link Layer User's Guide"
developer.nordicsemi.com...
Hi,
I've been working with a two LPC1768 boards with connections to Addicore nRF24L01+ boards.
I have not been able to successfully receive an ack on the PTX board although...
Hello
What is a typical current draw when using a PORT GPIOTE interrupt? I seem to be drawing approximately 200uA with a port event enabled. Is this normal?
I'm using...
Here: developer.nordicsemi.com/.../a00050.html
"The Bootloader/DFU with SoftDevice update example shows how a SoftDevice, bootloader, and pplication (sic) can be updated...
Hi,
I am trying to bring up custom board with 51822 CFAC-A0.
And I am continuously getting the following error as soon as the code does advertising_start().
I am using...
This comment for this line of code in twi_sw_master.c is misleading:
#define TWI_DELAY() nrf_delay_us(4) /*!< Time to wait when pin states are changed. For fast-mode the...
Hello all
I'm new to Nordic products and the Keil compiler and in order to fast-track my development I have two computers, home and work, running Keil MDK-ARM (lite) with...
As said on the topic "GAP Address types", the random static address can be changed when system boots up. I can't find any content about how to make it. Could anyone offer...
Hello,
I have a problem with getting i2c to work. What I did is enabled the 2-wire block, and tried to send various data as a master(by setting the registers), but I cant...
Hi Nordics.
I want to change SDK version of my project from SDK 6 to SDK 8.1
(actually I am trying to restart my project with new SDK 8.1)
My project base on the ancs...
Hello all,
I am using the examples/peripheral/uart project, which by default is set up as follows:
Language = C
Dialect = C99
Language conformance = Standard with...
Hello,
I am developing on top of S110, for nrf51822_xxaa, building with GCC.
And as my code is growing, even after mapping inspection, gcc optimizations, stripping, heap...
