hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
i get the example for using PWM to run and modfied it to use it in my application. My Prolem is that i only have one PWM Output toggle Pin. How can i build a second...
Hi,
I'm using the MCP to send a long to a nrf6310 board loaded with SD v6. The board hangs when I send a long though, is this due to the MCP not being set up to send longs...
Hello,
I have the nRF51822 Evaluation Kit. I have run the basic code examples like 'Blinky' and the BlueTooth HRS (Heart Rate) application, successfully.
Now I would like...
Hi,
Is it possible to give a function address to the "Task End-Point" of a PPI channel?
Like :
err_code = sd_ppi_channel_assign(PPI_CHAN0_TO_TOGGLE_LED,
&(NRF_TIMER1...
I am designing a device that needs to operate both as a Peripheral (such as a Heart Rate sensor) and also as a Central so it can optionally connect and gather data from other...
Hi,
in my application I have a device that has to be controlled by a remote control. For transmitting data between the remote and the device I would like to use BLE (not...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
Hi,
does firmware or example source code exist for the PCA10000 USB dongle that implements the Bluetooth HID host?
I would like to use it as receiver for the Nordic Smart...
Hi all,
I am trying to specify a fixed port for a L2CAP connection on the nRF51822. The client is a Linux box running bluez (which has BLE support). The client software...
Hi,
Just bought the nRF51822 eval kit. Looks like it came with some great demos for iPhone (nRF_Demo_Utility, nRF_Proximity, nRF_Temp, nRF_UART), but having trouble getting...
Hi,
I upgraded to the 4.3 nRF51 last night and am suddenly having a whole slew of issues:
(1) When flashing the EK, the Segger now reports 257K of Flash (maybe it did...
